Tri-Band Repeater Kit for AT&T & US Cellular 4G LTE [Discontinued]

0 0

There is a New Version of this Product

The Tri-Band Repeater Kit has been discontinued and replaced by the new and improved Wilson 461104 AG Pro Quint 70dB Signal Booster Kit.

Go to the new Wilson Ag Pro Quint

Availability: Out of stock

$1,099.95
SureCall

Get it Faster!

Orders placed by 4pm EST typically ship the same day.

Questions? We're here to help:

(800) 590-3564

Description

Details

The Tri-Band Repeater Kit for AT&T & US Cellular 4G LTE features a powerful dual-band amplifier that can cover most carrier's 2G and 3G networks combined with a 4G LTE amplifier for boosting the AT&T and US Cellular 4G LTE networks.  Until now, most signal boosters were either dual-band and only boosted 3G and earlier signals or they were LTE specific and only boosted the LTE signal, which is only used for data and not voice calls. This system combines the two and boosts both the dual-band and AT&T & US Cellular LTE frequencies giving you crystal clear phone calls with blazing fast 4G LTE data speeds.

This kit features a 65 dB dual-band amplifier and a 70 dB 4G LTE amplifier.  With a strong outside signal, the dual-band amplifier will cover up to 7,500 sq ft while the LTE signal will cover up to 10,000 sq ft.  You can control the gain of each individual frequency allowing the installer to fine tune the system to ensure maximum coverage without any interference.

Kit Includes:

Installation

To install, start by mounting the yagi antenna as high as possible in a location that receives the best signal and where it won't shoot over the building when aimed at the tower. The Yagi antenna includes hardware for mounting the antenna to a pole of up to 2 in. in diameter. Run one of the coax cables from the antenna, into the building, and connect it to one of the diplexers. Connect a 2 ft. cable to each output port of the diplexer. To the LOW side of the diplexer, attach the Outside Antenna port of the CM700A LTE amplifier. To the HIGH side of the diplexer, attach the Outside Antenna port of the EFlex-65 dual-band amplifier. To the Inside Antenna ports of each amplifier, attach 2 ft. cables, and then connect them to the corresponding ports of the second diplexer (LTE to LOW, Dual-Band to HIGH). Connect the remaining coax cable to the remaining port on the diplexer, and then connect the dome antenna. Mount the dome antenna in the middle of the area to the covered.


* except Nextel and T-Mobile

Additional Info

Additional Info

Max Coverage Area Up to 7,500 sq ft
Frequency 700MHz, 800MHz, 1900MHz
Specific Frequency (Up/Down) 698 - 716 MHz / 728 - 746 MHz, 824 - 849 MHz / 869 - 894 MHz, 1850 - 1910 MHz / 1930 - 1990 MHz
Gain No
Impedance 50 ohm
Product Manual No
Product Specifications No
Power Requirements No
FCC Notice
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.

Please note, the four largest carriers - AT&T, T-Mobile, Verizon and Sprint - and more than 90 regional carriers have given blanket consent for use of all boosters certified to the new FCC standards.

Customer Reviews