The Wilson 842772-UB Tri-Band 4G-C has been discontinued.
Please contact us to learn about available replacement products.
Wilson's 842772-UB Tri-Band 4G-C Signal Booster Kit with omnidirectional antenna is the first consumer wireless signal booster from Wilson designed specifically to boost AWS in addition to the standard Dual-Band frequencies. Until now, most signal boosters were either dual-band and only boosted 3G and earlier signals or they were AWS specific and only boosted the AWS signal. This amplifier combines the two and boosts both the dual-band and AWS frequencies making it the ideal amplifier for carriers like T-Mobile, Boost Mobile, Cricket Wireless, and most Canadian carriers. The amplifier's standard dual-band frequencies (850MHz Cellular and 1900MHz PCS) will boost most major cell carriers 2G and 3G networks. The additional AWS 1700/2100 MHz capability amplifies the frequencies used by T-Mobile, Boost Mobile, Cricket Wireless, and most Canadian 4G networks.
The Wilson 802770 Tri-Band 4G-C repeater for AWS features a 70 dB gain which gives it a total coverage area of up to 15,000 sq ft (depending on existing outside signal strength) when paired with the included omnidirectional antenna making this the ideal amplifier for large homes and small to medium offices. For up to 20,000 sq ft of coverage, check out the the Wilson 842773-UB Tri-Band 4G-C Premium Kit for AWS & Dual-Band Networks with directional antenna.
Because this is a powerful amplifier, you must have a minimum of 20 ft of vertical separation between the inside and outside antennas. Adding up to 75 feet of horizontal separation can help improve the performance of this signal booster by minimizing the potential for oscillation (feedback) between the inside and outside antennas.
- Wilson 802770 Tri-Band 4G-C 70dB Amplifier for Dual-Band & AWS
- SureCall Full Band Fiberglass Omnidirectional Antenna (CM288W)
- Wilson 50 Ohm Wide Band Interior Panel Antenna (301135)
- 2 x Wilson 50' Ultra Low Loss Coax Cable (952350)
More Wilson 802770 Tri-Band 4G-C Kit Options
This kit is best for locations where the existing signal strength outside is 3 or fewer bars. The included directional antenna must be aimed so this kit can only cover the carriers with towers in a single general direction. If you have carriers with towers in multiple directions, an additional outside antenna can be added, contact us for more information.
As low as: $849.95
If the existing Omni and Yagi kits don't suit your needs, you can pick and choose the exact components that will work best in your situation. Feel free to contact us for assistance.
If you already have the cables and antennas and only need the amplifier, then this is the best option for you.
|Max Coverage Area||Up to 10,000 sq ft|
|Frequency||800MHz, 1900MHz, 1700/2100MHz|
|Specific Frequency (Up/Down)||824 - 849 MHz / 869 - 894 MHz, 1850 - 1910 MHz / 1930 - 1990 MHz, 1710 - 1755 MHz / 2110 - 2155 MHz|
|Gain||70dB / 70dB|
|Product Manual||Wilson Tri-Band 4G-C Signal Booster Installation Guide|
|Power Requirements||6 V, 1.5 A - 3.0 A|
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
Please note, the four largest carriers - AT&T, T-Mobile, Verizon and Sprint - and more than 90 regional carriers have given blanket consent for use of all boosters certified to the new FCC standards.