Wilson 460103 DB Pro 4G 65dB Signal Booster Kit - Voice, 3G & 4G LTE for all Carriers [Discontinued]

The Wilson 460103 DB Pro 4G has been discontinued and is being replaced by the new weBoost 470103 Connect 4G Signal Booster Kit. You Should Choose This Kit If You need an all in one solution to provide boosted voice calls plus 3G and 4G LTE data for one carrier (or multiple carriers with towers in the same general direction) and require coverage for an area up to 5,000 sq ft.* over one or multiple floors. To cover a larger area inside, check out our Wilson 461104 AG Pro Quint 70dB Signal Booster Kit. The DB Pro 4G comes with a directional outside antenna.  Directional antennas must be aimed, which is easy to do through trial and error, but are limited to covering carriers with towers in one general direction.  To boost the signal from multiple carriers with towers in different directions, you will need to add additional directional outside antennas or switch to an omnidirectional outside antenna.  Contact us to hear about both options. Coverage Area Many variables impact the total coverage area of a signal booster system. The following are estimates only and may not be accurate in any individual situation. If you have an existing strong 5-bar outside signal, you may get up to 5,000 sq ft of coverage inside* If you have an existing 3 to 4-bar (-90 dB) outside signal, you may get up to 4,000 sq ft of coverage inside* If you have an existing 1 to 2-bar (-100 dB) outside signal, you may get up to 500 sq ft of coverage inside* Supported Carriers The DB Pro 4G supports the Voice, 3G, and 4G LTE networks from all major carriers in North America.  It does not support any WiMAX or iDEN networks. The DB Pro 4G amplifier is currently only available for shipment within the Untied States. For Canadian and Mexican carriers, try the Wilson 842772 Tri-Band 4G-C. AT&T 2G, 3G, 4G HSPA+ & 4G LTE Verizon 2G, 3G & 4G LTE Sprint 2G, 3G & 4G LTE T-Mobile 2G, 3G, 4G HSPA+ & 4G LTE US Cellular 2G, 3G & 4G LTE All other carriers using 800 MHz, 1900 MHz, and AWS 1700/2100 MHz Kit Includes The Wilson 460103 DB PRO 4G Yagi Kit comes with everything necessary for installation.  Some installations may require additional parts so see the Accessories section below for more details. 460003 - Wilson 5-Band DB Pro 4G 65 dB Amplifier 314475 - Wide-Band Directional Antenna with F-Female Connector 311155 - Wide-Band Panel Antenna with F-Female Connector 950630 - 30' White RG6 Low Loss Coax Cable (for use with Inside Antenna) 950630 - 30' White RG6 Low Loss Coax Cable (for use with Outside Antenna) Antenna Hardware Mounting Kit Instruction Manual Accessories We recommend a lightning protector kit for all installations in areas that have lightning or thunderstorms. The lightning protector has a gas discharge element that severs the connection to the amplifier if a power surge comes from the outside antenna. The included Directional Outside antenna requires pole to mount the antenna. If you do not have an existing pole, consider including the 901117 Pole Mounting Assembly.  Installation Overview The DB Pro is easy to install for anyone that's a bit handy. But if you're not comfortable getting up on your roof to mount an antenna, it may be best to find an electronics installer or a handy friend. We always recommend doing a soft install where you don't permanently mount anything or drill any holes until you know the system will work for you and you've identified the best locations for the antennas.  To install, just follow these 4 steps: To start, you'll need to find a place on the roof of your home or office to mount the outside yagi antenna. It's best to figure out which direction it will need to be pointed before permanently mounting the antenna which we'll cover at the end. Connect the 30 ft. RG-6 coax cables to the antenna and run it into the house. You may be able to enter through a vent or a soffit; otherwise, you may have to drill a hole.  With the cable inside, connect it to an in-line lighting protector if you purchased one, and then to the amplifier. To the inside antenna port on amplifier, connect the 30 ft. RG-6 cable and then connect the inside antenna. If you have an attic, the easiest installation method is typically to have the amplifier and inside antenna in the attic with the panel antenna face down on the floor in the middle of the house. If you don't have an attic, you can mount the panel antenna on the ceiling in the middle of the house, or on a wall. Once all of the components are connected, plug in the amplifier and see if you get any error lights. A red light indicates that the inside and outside antennas are too close together. Unplug the amplifier and then increase the separation between the antennas and try again. If you can't increase the separation, you can turn down the gain on the amplifier which will also decrease the total coverage area. For any other errors, consult the manual or contact us for help. To aim the yagi antenna, start with the antenna high on the roof pointed in one direction. Turn on the system and have an inside helper inside stand near the inside antenna and take a signal reading with their phone in field test mode. Rotate the yagi antenna 45 degrees and then pause for 30 to 60 seconds. After the pause, the person inside should take another signal reading, and then you can repeat the process. Each time your partner checks the signal strength, also check to make sure there aren't any warning lights on the amplifier. After you've gone all the way around, mount the antenna facing in the direction with the strongest signal. If possible, also mount the antenna on that side of the home or office so that it's pointing away from the building and not over the building. The included manual is very helpful and we recommend reading through it before beginning the installation. If you run into any issues, feel free to contact us for help.  Benefits Everything you need is in the box, just set it up and go Reduces dropped calls and increases data speeds Works wirelessly so you can use your cell phone like you always do Supports multiple phones and data devices simultaneously Adjustable per-frequency gain control makes installation easier Contains carrier protection technologies to guard against overload and oscillation Amplifies the signal both to and from the cell carrier Boost all 5 freuquencies that are commonly used for 2G, 3G, and 4G LTE in North America Extends the battery life of your phone Made in the USA FCC and IC type accepted * The actual coverage area of a signal booster is dependent on many factors including existing outside signal strength, obstructions between you and the cell tower, the materials used in your home or office, the layout of the area you need to cover with a boosted signal, and other factors. The approximate coverage areas listed above are estimates. Actual coverage area will vary based on these and other factors. If you're not sure if a system will be powerful enough for your needs, contact us to find out.